================================================================================
Express5800/D120h
System BIOS F33
================================================================================
Software name : Express5800/D120h
System BIOS update module
Models : Express5800/D120h
Operating System : This software supports offline update
- updating with CD/DVD medium
Target Users : See [Target Users for Update] below
Type : System BIOS
================================================================================
[ About the software ]
The Express5800/D120h System BIOS update module (hereinafter called "the
Software") supports the following functional enhancement of Express5800/D120h:
- Updated microcode and SPS firmware for Intel(R) Xeon(R) Scalable Processors.
This version mitigates the security vulnerabilities of INTEL-SA-00185,
INTEL-SA-00191, INTEL-SA-00223 and INTEL-SA-00233, which were announced by
Intel Corporation.
- Made a fix not to register the unnecessary SEL indicating the processor
configuration error.
** Note for update from F16 BIOS **
* BIOS SETUP menu setting will be changed to the default setting after you use
this software. Please backup BIOS SETUP setting with "BIOS SETUP Backup/
Restore Tool" attached to the product. And also please restore setting after
BIOS update.
Please refer readme file attached with BIOS SETUP Backup/Restore Tool for
the detail.
** Cautions in general **
* An incorrect update could result in a failure, such as the system fails to
boot. For a successful update, read this document carefully and follow the
instructions.
Should your system malfunction or be powered off due to an unplanned event
(such as a blackout, a cutoff, lightning, and noise) during the update, the
system may be damaged and fail to operate normally. In such a case, the
system may need to be repaired at your expense.
* When the Windows(R) BitLocker(TM) feature is enabled, disable it before the
update. After the update is completed, enable the feature again. Without
disabling the function before the update, booting the system may require the
recovery password.
-------------------------------------------------------------------------------
[ Target Users for Update ]
This software is available for customers using the following models with the
following BIOS version.
- Supported models
1.Express5800/D120h
- Supported BIOS version
1. F16
2. F19
3. F21
4. F24
5. F30
Note: This update is not necessary if the above BIOS version is older than yours,
which already includes the equivalent enhancements and modifications to be
added by the Software.
Your system BIOS version can be checked in any of the following ways:
<On BIOS Setup Utility>
1. Power on the system then the screen shows the process of the POST (Power
On Self-Test). After a short time, the following message appears:
Press <DEL> to enter SETUP
Then press the DEL key to start up BIOS Setup Utility.
2. The "Main" menu shows your BIOS version.
Note: To exit BIOS SETUP Utility, move the cursor with the left or right key
to the position of "Save & Exit" and then select "Discard Changes and
Exit."
Note: For details on how to use BIOS SETUP Utility, refer to "System BIOS" in
the chapter of "Useful Features" in the maintenance guide.
<On the Windows(R) OS>
1. Hold down the Windows key and press the R key.
2. In the "Run" dialog box, type "msinfo32" and then click "OK."
3. After the "System Information" window opens, select "System Summary."
4. Check the "BIOS Version/Date" item for your BIOS version.
<On the Linux(R) OSS>
1. Start a terminal emulator such as xterm.
2. Execute the following command:
# /usr/sbin/dmidecode | less
Note: This # means a prompt. You do not need to input the symbol.
3. Check the BIOS Information->Version item for your BIOS version.
Note: The dmidecode command has to be installed in advance.
Be certain to read carefully the following NEC software license agreement
before applying this software update module. If you can not agree to the terms
of the agreement, do not download this software. By downloading the software
you will be bounded by the terms of the agreement.
[User License Agreement]
NEC Corporation ("NEC") grants you the right to use the software program
("Software") under the terms and conditions of this Agreement only in the
country in which you acquired the Software. You shall agree to all provisions
of this Agreement and assume responsibility for selection, installation, use
and effect of the Software purchased for your desired effect.
1. Terms
1.1 This Agreement shall come into force on the date of your receipt of the
Software.
1.2 You may terminate the license granted hereunder by notifying us in writing
at least one month prior to the desired termination date.
1.3 NEC may terminate the license granted you hereunder at any time if you
fail to comply with any terms and conditions of this Agreement.
1.4 The license to the Software shall remain in force until the license is
terminated on the date set forth hereunder.
1.5 Upon termination of the license, other rights granted you hereunder shall
also be terminated. You must destroy or dispose of the Software, any copies
of the Software and manual and other materials provided with the Software.
2. Copyright
2.1 The Software shall solely be used in the NEC Express5800 servers.
2.2 NEC grants you the right to use the Software only in the country in which
you acquired the Software in accordance with the conditions of the
preceding paragraph.
3. Copying, altering, and combining of the Software
3.1 You may only make one copy of the Software solely for a backup purpose,
provided, however, that the copy of the Software is loaded into permanent
memory of the system. You may store the Software solely to prevent damages
or loss of the memory media.
3.2 You shall place the copyright notice and other legends on each copy of the
Software.
3.3 You may not use, copy, alter, combine, publish, reproduce the Software over
the Internet, or otherwise dispose of the Software except as provided in
this Agreement.
3.4 You may not copy, publish the manual or other related documentation
provided with the Software, or reproduce such manual and documentation over
the Internet.
3.5 No intangible property right to the Software shall be transferred to you.
4. Transfer
4.1 You may assign your rights granted hereunder to a third party only if all
conditions below are satisfied:
a. You shall assign and shall not retain this Agreement, the Software, all
copies of the Software, or the manual or other related documentation
provided with the Software.
b. The transferee agrees to this Agreement.
4.2 You shall not sublicense, assign, transfer, or otherwise dispose of the
Software or the right of use to any third party except as provided herein.
5. Reverse compile
You may not reverse engineer, decompile, or otherwise disassemble the
Software.
6. Limitation of warranties
6.1 The Software is provided "as is" without warranty of any kind. In no event
shall NEC be liable with respect to any claim by you on account of or
arising out of the use of the Software.
6.2 Notwithstanding the provisions of the preceding paragraph, in case NEC
makes any bug-fix version to the Software, NEC will, at its expense,
furnish you with such bug-fix version, update version, or information in
relation to such bug-fix or update version both in the source code form and
object code form, and such bug-fix version or update version shall be
considered as the licensed Software.
7. No liability
In no event shall NEC be liable for any indirect or consequential damages
or loss of profit or damages based on any third party claim, even if NEC
has been advised of the possibility of such damages.
================================================================================
BIOS Update Procedure
================================================================================
- Procedure at Offline
1.Download the module into any directory of hard disk.
2.Extract the module into any directory.
3.The software and README file will be extracted into the folder.
4.Execute the System BIOS Update following the README file.
You can refer to the README file by Notepad of Windows(R) OS.
--------------------------------------------------------------------------------
[Revision history]
09/20/2019 F33
- Updated microcode and SPS firmware for Intel(R) Xeon(R) Scalable Processors.
This version mitigates the security vulnerabilities of INTEL-SA-00185,
INTEL-SA-00191, INTEL-SA-00223 and INTEL-SA-00233, which were announced by
Intel Corporation.
- Made a fix not to register the unnecessary SEL indicating the processor
configuration error.
03/27/2019 F30
- Enhanced the improvement process against the issue that the following POST
error message appears:
Warning: VR program failure
09/26/2018 F24
- Updated microcode for Intel(R) Xeon(R) Scalable Processors.
This version mitigates the security vulnerabilities of INTEL-SA-00115 and
INTEL-SA-00161, which were announced by Intel Corporation.
- Fixed the issue that CentOS(R) 7.4 or later could not be booted.
- Fixed the issue that the following POST error message appeared.
Warning: VR program failure
- Made a fix not to register the unnecessary SEL indicating a processor error
correction.
Processor sensor configuration error was asserted
03/23/2018 F21
- Updated microcode for Intel(R) Xeon(R) Scalable Processors.
This version mitigates the security vulnerability of INTEL-SA-00088, which
was announced by Intel Corporation.
01/26/2018 F19
- Fix Intel SPS firmware for security issues below.
CVE-2017-5706 (https://www.cve.mitre.org/cgi-bin/cvename.cgi?name=2017-5706)
CVE-2017-5709 (https://www.cve.mitre.org/cgi-bin/cvename.cgi?name=2017-5709)
- Support static network interface name (Predictable Network Interface Name)
in Linux(R) OS.
- Fix rarely possible watchdog timeout at system boot.
- Fix issue [N8171-32] and [N8171-34] monitors can't show screen.
- Add [IMC Interleave] menu in BIOS SETUP utility.
- Improve not to show [Turbo Mode] and [Hyper-Threading] setting in BIOS SETUP
menu for [N8101-1092] and [N8101-1093] processors which don't support Turbo
Mode or Hyper-Threading.
--------------------------------------------------------------------------------
[Copyright and trademark]
Microsoft, Windows, Windows Server are trademarks or registered trademarks of
Microsoft Corporation in the United States and other countries.
Linux(R) is the registered trademark of Linus Torvalds in the United States and
other countries.
Red Hat and Red Hat Enterprise Linux are trademarks or registered trademarks of
Red Hat, Inc. in the United States and other countries.
All other company names and product names mentioned herein are trademarks or
registered trademarks of their respective owners.
The copyright of the Software is owned by NEC Corporation or the third-party
software developer. All other products mentioned herein are copyrighted works
of their respective manufacturers.
--------------------------------------------------------------------------------
Copyright NEC Corporation 2019