===============================================================================
LSI Embedded MegaRAID(tm) Windows Driver Update Module Version 9.34.0820.2008
===============================================================================
Software name : LSI Embedded MegaRAID(tm) Windows Driver Update Module
Version 9.34.0820.2008
Registered name : Megasr0934.exe
Copyright (C) : LSI Corporation
Models : See below
Operating system: See below
Software type : Driver / RAID controller
Creation method : Self-extracting
===============================================================================
[ About the software ]
The LSI Embedded MegaRAID(tm) Windows Driver Update Module ("the Software")
resolves the following issues in the NEC Express5800 servers:
- Fails to collect the memory dump uncommonly if the N8104-123A 10GBASE-SR
is installed.
- Detects the data inconsistency error in the unused area during the consistency
check operation.
--------------------------------------------------------------------------------
[ Models, OS and software revision to update ]
The following servers with operating system and driver versions stated below
require the driver update:
- Models:
NEC Express5800/120Rh-1
NEC Express5800/120Ei
NEC Express5800/110Ri-1
NEC Express5800/110Ge
NEC Express5800/i120Ra-e1
- Operating System:
Windows Server 2003 Standard Edition
Windows Server 2003 Enterprise Edition
Windows Server 2003 Standard x64 Edition
Windows Server 2003 Enterprise x64 Edition
Windows Server 2003 R2, Standard Edition
Windows Server 2003 R2, Enterprise Edition
Windows Server 2003 R2, Standard x64 Edition
Windows Server 2003 R2, Enterprise x64 Edition
- Driver version:
9.33.0416.2008 or earlier
Note: The driver version later than 9.34.0820.2008 do not require the update.
Please read the following User License Agreement ("Agreement") carefully. If
you do not agree to the terms and conditions of this Agreement, you shall not
download the Software. Downloading the Software indicates your acceptance of
the terms and conditions of the Agreement.
-------------------------------------------------------------------------------
[ User License Agreement ]
NEC Corporation ("NEC") grants you the right to use the Software under the
terms and conditions of this Agreement only in the country in which you
acquired the Software. You shall agree to all provisions of this Agreement and
assume responsibility for selection, installation, use and effect of the
Software purchased for your desired effect.
1. Terms
1.1 This Agreement shall come into force on the date of your receipt of the
Software.
1.2 You may terminate the license granted hereunder by notifying us in writing
at least one month prior to the desired termination date.
1.3 NEC may terminate the license granted you hereunder at any time if you
fail to comply with any terms and conditions of this Agreement.
1.4 The license to the Software shall remain in force until the license is
terminated on the date set forth hereunder.
1.5 Upon termination of the license, other rights granted you hereunder shall
also be terminated. You must destroy or dispose of the Software, any copies
of the Software and manual and other materials provided with the Software.
2. Copyright
2.1 The Software shall solely be used in the NEC Express5800 servers.
2.2 NEC grants you the right to use the Software only in the country in which
you acquired the Software in accordance with the conditions of the
preceding paragraph.
3. Copying, altering, and combining of the Software
3.1 You may only make one copy of the Software solely for a backup purpose,
provided, however, that the copy of the Software is loaded into permanent
memory of the system. You may store the Software solely to prevent damages
or loss of the memory media.
3.2 You shall place the copyright notice and other legends on each copy of the
Software.
3.3 You may not use, copy, alter, combine, publish, reproduce the Software over
the Internet, or otherwise dispose of the Software except as provided in
this Agreement.
3.4 You may not copy, publish the manual or other related documentation
provided with the Software, or reproduce such manual and documentation over
the Internet.
3.5 No intangible property right to the Software shall be transferred to you.
4. Transfer
4.1 You may assign your rights granted hereunder to a third party only if all
conditions below are satisfied:
a. You shall assign and shall not retain this Agreement, the Software, all
copies of the Software, or the manual or other related documentation
provided with the Software.
b. The transferee agrees to this Agreement.
4.2 You shall not sublicense, assign, transfer, or otherwise dispose of the
Software or the right of use to any third party except as provided herein.
5. Reverse compile
You may not reverse engineer, decompile, or otherwise disassemble the Software.
6. Limitation of warranties
6.1 The Software is provided "as is" without warranty of any kind. In no event
shall NEC be liable with respect to any claim by you on account of or
arising out of the use of the Software.
6.2 Notwithstanding the provisions of the preceding paragraph, in case NEC
makes any bug-fix version to the Software, NEC will, at its expense,
furnish you with such bug-fix version, update version, or information in
relation to such bug-fix or update version both in the source code form and
object code form, and such bug-fix version or update version shall be
considered as the licensed Software.
7. No liability
In no event shall NEC be liable for any indirect or consequential damages or
loss of profit or damages based on any third party claim, even if NEC has been
advised of the possibility of such damages.
8. Others
You must agree that any disputes concerning this Agreement will be settled at
the Tokyo district court as the exclusively appointed court.
-------------------------------------------------------------------------------
[ Driver update procedures ]
Perform the following steps to extract the Software and update the driver.
- How to extract:
(1) Download Megasr0934.EXE to a desired directory. (for example, "C:\TEMP"
folder)
(2) Click [Start] button and then click [Run...].
(3) Enter "C:\TEMP\Megasr0934.EXE" in the "Open" field, and then click [OK].
(4) Enter the folder name to store the extracted files, and then click the
[Unzip] button.
- How to update:
(1) Find and refer to Readme_Eng.txt.
-------------------------------------------------------------------------------
[ Trademarks and copyright ]
The copyright for this software is held by LSI Corporation.
Microsoft and its logos, and Windows and Windows Server are registered
trademarks or trademarks of the Microsoft Corporation in the U.S. and other
countries.
LSI and the LSI logo design are trademarks or registered trademarks of
LSI Corporation.
All other company and product names are trademarks or registered trademarks of
their respective owners.
-------------------------------------------------------------------------------
Copyright NEC Corporation 2009