NEC Express5800 Web Site (Asia Pacific)
================================================================================
NEC Express5800/120Li (N8100-1239F,1240F)
BMC firmware 00.45 update for Windows
================================================================================
[ Software name ] NEC Express5800/120Li BMC firmware update for Windows
[ Registered name ] U4503CBW.zip
[ Applicable models ] NEC Express5800/120Li
[ Users ] See below [Users whose system needs to be updated].
[ Software type ] BMC Firmware
[ Creation method ] ZIP archived
--------------------------------------------------------------------------------
[ Software introduction ]
This BMC Firmware (BMC Firmware Revision 00.45) is programmed allow the NEC
Express5800/120Li Server to support the remote media functions.
Notes: Incorrect update operations may cause a system start failure.
Read this explanation thoroughly, until fully understanding the correct system
update procedures. If an unexpected problem arises (e.g., power failure, lightning,
shutdown, or noise) during the data rewrite process, a system malfunction or the power
supply loss may occur, resulting in equipment damaged, which may cause the equipment to
fail or operate incorrectly. In such a case, repair expenses may be charged to the customer.
[ Users whose system needs to be updated ]
Models with BMC Firmware versions which fit the descriptions below will require
BMC Firmware updating.
- Models
NEC Express5800/120Li: N8100-1239F,N8100-1240F
- Software versions
(1)BMC Firmware Revision: 00.44
Notes: If the software versions of the present system are newer than the above
stated revisions, the system does not require software updating. Functions equivalent to
those of these software updates will have already been applied..
Be certain to confirm the software versions of your system.
Version confirmation procedures:
(1) Power on the machine.
(2) When the following message appears, press the F2 key to start the BIOS Setup Menu.
"Press <F2> to enter SETUP"
(3) Using the arrow keys, move the cursor to [Server].
(4) Select the [System Management] sub menu and press the Enter key.
(5) The software versions of your system will be displayed.
(6) After confirmation of the software versions, press the ESC key and exit
the [System Management] sub menu.
(7) Move the cursor to [Exit], using the arrow keys.
(8) Select [Exit Discarding Changes], and exit the BIOS Setup Menu.
(*)
Refer to the User's Guide for details on BIOS Setup.
Be certain to read carefully the following NEC software license agreement before
applying this software update module. If you can not agree to the terms of the agreement,
do not download this software. By downloading the software you will be bounded
by the terms of the agreement.
[ User license agreement for NEC software ]
This user license agreement is an agreement between you and the NEC Corporation
(hereinafter referred to as NEC). Under the following terms of agreement, NEC grants
you the right to utilize this software program (hereinafter referred to as
"licensed program"), but the customer will be bound to these to the terms.
NEC will not be held liable for the use, installation, or the results of the
use of the licensed program.
1. Terms
(1) This user license agreement takes effect from the day the software product is
received by the user.
(2) You may terminate your rights to use the licensed program under this user
license agreement at any time, by notifying NEC, in writing, at least one month or
longer prior to the requested date of termination.
(3) NEC reserves the right to terminate this license agreement if you violate
any of the provisions in this agreement.
(4) Your rights to use the licensed program will continue until it is terminated
in accordance with the provisions stated in this license agreement.
(5) If the agreement is terminated for any reason by either party, you are required
to destroy the software, copies of the software and its manuals and media,
or return them to NEC immediately.
2. Usage right
You may use the licensed program only on NEC Express server (NEC Express5800/100 series)
using your Microsoft(R) Windows(R) 2000, Windows Server(TM) 2003.
3. Copying, altering, and combining of the licensed program
(1) You are granted the permission to create on copy of the licensed program to use
as a backup in case the program data becomes lost, damaged or destroyed. Once the
licensed program is loaded into memory on a PC, a copy of the program may be stored
only as backup incase the fixed memory of the PC becomes damaged or lost.
(2) The copyrights and license agreement must be attached to all copies of the
licensed program.
(3) Unless otherwise specified in this user license agreement, you may not use, copy,
alter the licensed program or combine it with another module. It may not reproduced
in any publications or networks. The handling of the licensed program and/or documents
must strictly follow the terms and conditions of this license agreement, and at
no time shall it be handled in any other terms.
(4) All related documents (e.g., manuals) provided with the licensed program
may not be copied, altered or reproduced in any publications or networks, under
any circumstances.
(5) This user license agreement does not transfer the intellectual property
of the licensed program to the user.
4. Transfer of the licensed program
(1) All rights of this license agreement may be transferred to another party ONLY
when the following conditions are satisfied:
(a) All materials including the licensed program, all copies of the licensed program,
this license agreement, and all other related documents are transferred to the other
party, and no material concerning the licensed program is retained by you.
(b) The recipient party agrees to conform to the terms of this user license agreement.
(2) Unless otherwise specified in this user license agreement, the licensed program
or rights for its use may not be transferred to a third party. All matters concerning
the transferring of the rights and program must strictly follow the terms and
conditions included in this license agreement.
5. Decompilation
You may not reverse engineer, decompile, or disassemble the licensed program.
6. Term of a guarantee
(1) NEC makes no warranties, expressed or implied concerning this licensed program,
and will at no time, be held liable to pay for any expenses which may be incurred,
should a problem result from the use of the licensed program.
(2) Regardless of the terms stated above in term (1), upon correction of the
licensed program errors (bugs), NEC may, at its own discretion, release an update
patch for error-correction (hereinafter referred to as modification program),
or information, including NEC approved method of error correction. The modification
program provided to you will be regarded as the licensed program, and will follow
the terms and conditions of this license agreement.
7. No liability
In no event shall NEC be held responsible for any indirect, direct or consequential
damages (including damages which NEC can or can not foresee) which may be claimed
to you by a third party.
8. Others
The user must agree that any disputes concerning this user license agreement will be
settled at the Tokyo district court as the exclusively appointed court.
--------------------------------------------------------------------------------
Installation proccess
--------------------------------------------------------------------------------
Use the following procedure to extract and install this software.
[ Extraction procedure ]
(1) Download "U4503CBW.zip" to a desired suitable location on your hard disk.
(2) Unzip U4503CBW.zip to a suitable location.
This software will be extract under the 'U4503CBW' folder.
[ Install procedure ]
(1) Execute "setup.exe" under the "U4503CBW" folder. The BMC firmware update
process will be started.
(2) After the BMC firmware update process is completed,
the new BMC firmware will be applied, when the system power off and power up.
[ Notes of restarting operation ]
Please close web browser and reopen, if you are using the BMC Web server
function on the management PC.
Please confirm that J2SE Runtime Environment 5.0 or later is applied
on management PC.
-------------------------------------------------------------------------------------------
[Trademarks and Copyright]
The copyright for this software is held by NEC.
*Microsoft and Windows are registered trademark of US Microsoft Corporation in
the United States and other countries.
*All other company and product names in this document are the registered trademark
or trademark of their respective owners.
-------------------------------------------------------------------------------------------
Copyright NEC Corporation 2006