================================================================================
Release Notes for System BIOS Phoenix cME(tm) TrustedCore(tm) Server Release
Phoenix cME(tm) TrustedCore(tm) Server Release 1.0.2019
================================================================================
[Software] NEC Express5800/140Rf-4
System BIOS update module for Windows
[File Name] W44A0119.EXE
[Supported Models] NEC Express5800/140Rf-4
(N8100-1364F/N8100-1365F)
[Supported OS] As follows
- Windows Server 2003
- Windows Server 2008
[Users who need update] See below
[Type of software] System BIOS
[How to create] Self executable
================================================================================
[Software introduction]
The System BIOS Phoenix cME(tm) TrustedCore(tm) Server Release Phoenix cME(tm)
TrustedCore(tm) Server Release 1.0.2019(hereinafter the "Software")supports the
following functional enhancement in the NEC NEC Express5800/140Rf-4 models:
- Supported Windows Server(R) 2008
- Updated critical microcode
for DualCore Intel(R)Xeon(R) Processor 7200 series
- Updated critical microcode
for QuadCore Intel(R)Xeon(R) Processor 7300 series
Note:
- To prevent a system failure, please read this document carefully and follow
the procedure for successful update. Should your system malfunctions or is
powered off due to an unplanned event during update (for example, power
blackout or cutoff, lightening, and noise), the system may be damaged and
fails to operate normally. In this case, any remedial measures shall be
taken at your expense.
- Before considering the implementation of Windows Server(R) 2008, be sure to
refer to the Hardware Information located in the NEC Express5800 Series
Windows Server(R) 2008 Information pages for hardware configurations.
- To use Windows Server(R) 2008, read thoroughly the Manual located in the
NEC Express5800 Series Windows Server(R) 2008 Information pages prior to
installation, so that no erroneous operation will be conducted.
- To prevent the operating system boot failure, please record and restore
the boot order of BIOS Setup Menu.
- If Windows(R) BitLocker(TM) is enabled on your system, please disable it
temporarily during BIOS update. If you don't turn it off, you may need
"recovery password" after BIOS update.
This software does not support virtualization environment.
[ Users whose system needs to be updated ]
Models with BIOS versions which fit the descriptions below will require BIOS
updating.
- Models
1.NEC Express5800/140Rf-4 N8100-1364F/N8100-1365F
- BIOS versions
1. Phoenix cME(tm) TrustedCore(tm) Server Release 1.0.2014
2. Phoenix cME(tm) TrustedCore(tm) Server Release 1.0.2015
NOTE:
If your BIOS version is later than the above, you do not need to update. Your
current BIOS already includes the functionality that the latest update module
will provide.
Be sure to confirm your BIOS version by following the steps below:
If you use Microsoft(R) Windows Server(R) 2003, confirm your BIOS version by
following the steps below:
1) Click Start - All Programs - Accessories - System Tools
- System Information.
2) Select System Summary.
3) See BIOS Version/Date for your BIOS version.
If you use Microsoft(R) Windows Server(R) 2008, confirm your BIOS version by
following the steps below:
1) Click Start - All Programs - Accessories - System Tools
- System Information.
2) Select System Summary.
3) See BIOS Version/Date for your BIOS version.
Be certain to read carefully the following NEC software license agreement
before applying this software update module. If you can not agree to the terms
of the agreement, do not download this software. By downloading the software
you will be bounded by the terms of the agreement.
[ License Agreement ]
NEC Corporation (hereinafter referred to as "NEC") grants you a personal and
non-exclusive license to use the software (hereinafter referred to as the
"Software") provided only on one machine at any one time.
Under the following terms of agreement, NEC grants you the right to utilize this
software program (hereinafter referred to as "Software"), but the customer will
be bound to these to the terms.
NEC will not be held liable for the use, installation, or the results of the use
of the licensed program.
1 Period
1.1 This Agreement shall come into force on the date of your receipt of the
Software.
1.2 You may terminate the license granted hereunder by notifying us in
writing at least one month prior to the desired termination date.
1.3 NEC may terminate the license granted you hereunder at any time if you
fail to comply with any terms and conditions of this Agreement.
1.4 Your rights to use the Software will continue until it is terminated in
accordance with the provisions stated in this license agreement.
1.5 Upon termination of the license, other rights granted you hereunder shall
also be terminated You must destroy or dispose of the Software, any
copies of the Software and manual and other materials provided with the
Software.
2 Usage right
The Software shall solely be used in the NEC Express5800 server and
workstation products that operate Microsoft(R) Windows(R) 2000,
Windows Server(R) 2003, Windows Server(R) 2008, Windows(R) XP.
3 Copying, modifying, and combining
3.1 You are granted the permission to create one copy of the Software to use
as a backup in case the program data becomes lost, damaged or destroyed.
Once the Software is loaded into memory on a PC, a copy of the program
may be stored only as backup incase the fixed memory of the PC becomes
damaged or lost.
3.2 The copyrights and license agreement must be attached to all copies of
the Software.
3.3 Unless otherwise specified in this user license agreement, you may not
use, copy, alter the Software or combine it with another module. It may
not reproduced in any publications or networks. The handling of the
licensed program and/or documents must strictly follow the terms and
conditions of this license agreement, and at no time shall it be handled
in any other terms.
3.4 All related documents (e.g., manuals) provided with the Software may not
be copied, altered or reproduced in any publications or networks, under
any circumstances.
3.5 This user license agreement does not transfer the intellectual property
of the licensed program to the user.
4 Transfer
4.1 All rights of this license agreement may be transferred to another party
ONLY when the following conditions are satisfied:
4.1.1 All materials including the Software, all copies of the Software, this
license agreement, and all other related documents are transferred to
the other party, and no material concerning the licensed program is
retained by you.
4.1.2 The recipient party agrees to conform to the terms of this user license
agreement.
4.2 UNLESS OTHERWISE SPECIFIED IN THIS USER LICENSE AGREEMENT, THE SOFTWARE
OR RIGHTS FOR ITS USE MAY NOT BE TRANSFERRED TO A THIRD PARTY. ALL
MATTERS CONCERNING THE TRANSFERRING OF THE RIGHTS AND PROGRAM MUST
STRICTLY FOLLOW THE TERMS AND CONDITIONS INCLUDED IN THIS LICENSE
AGREEMENT.
5 Reverse compile
You may not reverse engineer, decompile, or otherwise disassemble the
Software.
6 Limitation of warranties
6.1 NEC MAKES NO WARRANTIES, EXPRESSED OR IMPLIED CONCERNING THIS
SOFTWARE, AND WILL AT NO TIME, BE HELD LIABLE TO PAY FOR ANY EXPENSES
WHICH MAY BE INCURRED, SHOULD A PROBLEM RESULT FROM THE USE OF THE
SOFTWARE.
6.2 Regardless of the terms stated above in term 6.1, upon correction of
the Software errors (bugs), NEC may, at its own discretion, release an
update patch for error-correction (hereinafter referred to as
modification program), or information, including NEC approved method of
error correction. The modification program provided to you will be
regarded as the licensed program, and will follow the terms and
conditions of this license agreement.
7 Limitation of liabilities
In no event shall NEC be liable for any indirect or consequential
damages or loss of profit or damages based on any third party claim,
even if NEC has been advised of the possibility of such damages.
8 Other restrictions
The user must agree that any disputes concerning this user license
agreement will be settled at the Tokyo district court as the exclusively
appointed court.
================================================================================
BIOS Update Procedure
================================================================================
Perform the following procedure to update your BIOS.
[How to update]
1) Log in as an authorized user. (If you have logged in as an unauthorized user,
log out once and log in again as an authorized user.)
2) Download W44A0119.EXE to a folder in your hard disk drive.
(e.g. C: \TEMP)
3) Stop all applications you are using.
4) Click Start - Run.
5) Enter "C:\TEMP\W44A0119.EXE", and click OK to start the BIOS update tool.
6) Follow the instructions in the dialog boxes to update your BIOS. A progress
bar shows your update status.
7) When update is complete, the "InstallShield Wizard Complete" dialog box
appears. Check "Yes, Now restart computer" and click the Finish button to
reboot your system.
Note:
1. The latest BIOS will take effect after you reboot your system.
2. BIOS update logs are stored in:
%SystemDrive%\Program Files\NEC\OnlineBiosUpdate
3. If your operating system is running in Safe Mode, you cannot update your
BIOS.
The drive and folder names may vary by systems.
--------------------------------------------------------------------------------
[Revision history]
2008/07/14 Phoenix cME(tm) TrustedCore(tm) Server Release 1.0.2019
- Supported Windows Server(R) 2008
- Updated critical microcode
for DualCore Intel(R)Xeon(R) Processor 7200 series
- Updated critical microcode
for QuadCore Intel(R)Xeon(R) Processor 7300 series
- Change Default setting of Boot order in BIOS Setup Menu.
- Add USB HDD as 6th Device.
(*)USB Flash is recognized as USB HDD, if the capacity is 1GB or more.
USB Flash is recognized as USB KEY, if the capacity is less than 1GB.
[Legal notices (trademarks and copyrights)]
NEC Corporation and its third-party suppliers reserve the copyright to the
Software.
Microsoft, Windows, Windows Server, BitLocker are either registered trademarks
or trademarks of Microsoft Corporation in the United States and/or other
countries.
All other company names and product names mentioned herein are registered
trademarks or trademarks of their respective owners.
--------------------------------------------------------------------------------
Copyright NEC Corporation 2008