========================================================================================================= Express5800/T110h-S、Express5800/T110h、Express5800/R110h-1 BMC firmware 02.11 (offline update) ========================================================================================================= Software name : Express5800/T110h-S、Express5800/T110h、Express5800/R110h-1 BMC firmware update module for offline Models : Express5800/T110h-S、Express5800/T110h、Express5800/R110h-1 Software revisions: See below Type of software : BMC firmware --------------------------------------------------------------------------------------------------------- [ About the software ] BMC firmware and SDR update module("the software") supports the functional enhancement, which describe Revision history, in Express5800/T110h-S, Express5800/T110h and Express5800/R110h-1 models: Note: - To prevent a system failure, please read this document carefully and follow the procedure for successful update. Should your system malfunctions or is powered off due to an unplanned event during update (for example, power blackout or cutoff, lightening, and noise), the system may be damaged and fails to operate normally. In this case, any remedial measures shall be taken at your expense. - This software does not support virtualization environment. - If you use ESMPRO(R) ExpressUpdate function, [ 2. Models and software revisions for update ] and [ 3. Installation procedures ] are processed automatically. Please refrer to [ 4. Notes ]. - Before BMC firmware update, please make sure that a drive letter has been assigned to the virtual CD/DVD drive on Windows OS if the Remote Media function of the BMC firmware is enabled. [ Models and software revisions to update ] Users who use the following server models and BMC firmware versions need update: - Models to update: 1. Express5800/T110h-S 2. Express5800/T110h 3. Express5800/R110h-1 - BMC firmware and SDR versions to update: - BMC firmware BMC Firmware Revision: 02.06 02.08 NOTE: If your BMC firmware version is later than the above, you do not require the update (the latest versions already include the functions to be added by the software). - How to confirm your BMC Firmware version: Please make sure to confirm proper BMC Firmware version by any of the following means.(*1) * How to confirm by the server which will be updated * - By BIOS Setup, to confirm your BMC Firmware version: (1) Power on the system. (2) When the following message appears, press the F2 key to start the BIOS Setup Menu. "Press <F2> to enter SETUP" (3) Using the arrow keys, move the cursor to [Server]. (4) Select the [System Management] sub menu and press the Enter key. (5) The software versions of your system will be displayed. (6) After confirmation of the software versions, press the ESC key and exit the [System Management] sub menu. (7) Move the cursor to [Exit], using the arrow keys. (8) Select [Exit Discarding Changes], and exit the BIOS Setup Menu. * How to confirm by the remote access * - By EXPRESSSCOPE Engine 3, to confirm your BMC Firmware and SDR version: (1) Run EXPRESSSCOPE Engine 3. (2) Select the [system] tab. (3) Select the [IPMI information] sub menu. Confirmation of BMC Firmware version (4) Select the [MC] button and select [basbrd Mgmt Ctrl]. (5) Check [Firmware Revision]. - By ESMPRO Manager Ver.6, to confirm your BMC Firmware version: (1) Run ESMPRO Manager Ver.6. (2) After selecting the server, select the [Remote Control] tab. (3) Select the [IPMI Information] sub menu. Confirmation of BMC Firmware version (4) Select the [MC(Management Controller) Information] sub menu. (5) Select the [Basbrd Mgmt Ctlr] sub menu. (6) The BMC firmware version of your system will be displayed. Please read the following User License Agreement ("Agreement") carefully. If you do not agree to the terms and conditions of this Agreement, you shall not download the Software. Downloading the Software indicates your acceptance of the terms and conditions of the Agreement. [User License Agreement] NEC Corporation ("NEC") grants you the right to use the software program ("Software") under the terms and conditions of this Agreement only in the country in which you acquired the Software. You shall agree to all provisions of this Agreement and assume responsibility for selection, installation, use and effect of the Software purchased for your desired effect. The Software uses the software ("GPL Module") granted by GNU General Public License("GPL) or GNU Lesser General Public License("LGPL"). This Agreement does not cover GPL Module. The Software includes the following GPL Module and LGPL Module. <GPL Module> grep kbd procps libsepol pcmcia-cs initscripts SysVinit module-init-tools mingetty samba-client gdb bogl-bterm gpm slang syslinux libpci2 BusyBox dmidecode memtester cachetester ethtool TeDoLiF product <LGPL Module> glibc libtermcap glibc-common libusb alsa-lib newt You can distribute or change the module based on the conditions of GPL or LGPL or any later Version, stipulated by Free Software Foundation. The module is supposed to be useful, however, NEC does not guarantee it. In addition, NEC does not release any copyright of GPL Module, designed by NEC. == notice == The Free Software Foundation (FSF) is a non-profit corporation to support the spread of the free software. You need to refer to The Free Software Foundation ( https://www.fsf.org/ )for details of GNU General Public License Version 2 and GNU Lesser General Public License. You shall agree that NEC does not answer to any questions regarding the GPL Module. By using the Software including GPL Module, you will be bounded by the terms stipulated in GPL and LGPL. The following Agreement is applicable to the Software excluding GPL Module aforesaid. <Agreement for the Software> 1. Terms 1.1 This Agreement shall come into force on the date of your receipt of the Software. 1.2 You may terminate the license granted hereunder by notifying us in writing at least one month prior to the desired termination date. 1.3 NEC may terminate the license granted you hereunder at any time if you fail to comply with any terms and conditions of this Agreement. 1.4 The license to the Software shall remain in force until the license is terminated on the date set forth hereunder. 1.5 Upon termination of the license, other rights granted you hereunder shall also be terminated. You must destroy or dispose of the Software, any copies of the Software and manual and other materials provided with the Software. 2. Copyright 2.1 The Software shall solely be used in the NEC Express5800 servers. 2.2 NEC grants you the right to use the Software only in the country in which you acquired the Software in accordance with the conditions of the preceding paragraph. 3. Copying, altering, and combining of the Software 3.1 You may only make one copy of the Software solely for a backup purpose, provided, however, that the copy of the Software is loaded into permanent memory of the system. You may store the Software solely to prevent damages or loss of the memory media. 3.2 You shall place the copyright notice and other legends on each copy of the Software. 3.3 You may not use, copy, alter, combine, publish, reproduce the Software over the Internet, or otherwise dispose of the Software except as provided in this Agreement. 3.4 You may not copy, publish the manual or other related documentation provided with the Software, or reproduce such manual and documentation over the Internet. 3.5 No intangible property right to the Software shall be transferred to you. 4. Transfer 4.1 You may assign your rights granted hereunder to a third party only if all conditions below are satisfied: a. You shall assign and shall not retain this Agreement, the Software, allcopies of the Software, or the manual or other related documentationprovided with the Software. b. The transferee agrees to this Agreement. 4.2 You shall not sublicense, assign, transfer, or otherwise dispose of the Software or the right of use to any third party except as provided herein. 5. Reverse compile You may not reverse engineer, decompile, or otherwise disassemble the Software. 6. Limitation of warranties 6.1 The Software is provided "as is" without warranty of any kind. In no event shall NEC be liable with respect to any claim by you on account of or arising out of the use of the Software. 6.2 Notwithstanding the provisions of the preceding paragraph, in case NEC makes any bug-fix version to the Software, NEC will, at its expense, furnish you with such bug-fix version, update version, or information in relation to such bug-fix or update version both in the source code form and object code form, and such bug-fix version or update version shall be considered as the licensed Software. 7. No liability In no event shall NEC be liable for any indirect or consequential damages or loss of profit or damages based on any third party claim, even if NEC has been advised of the possibility of such damages. [ Installation procedures ] - Procedure at Offline 1.Check Secure Boot setting. If it is [Enabled], change it to [Disabled]. (Defualt setting is [Disabled].) If changing it, please return [Enabled] setting after this updating. * Secure Boot setting : BIOS Setup Utility - [Security] 2.Download the module into any directory of hard disk. 3.Extract the module into any directory. 4.The software and README file will be extracted into the folder. 5.Execute the BMC firmware Update following the README file. You can refer to the README file by Notepad of Windows(R) OS. --------------------------------------------------------------------------------------------------------- [ Revision history ] 2017/03/14 BMCFW Revision 02.11 BMC: - Updated OpenSSL module based on 1.0.2. - Changed some strings on Web browser and Command Line Interface of EXPRESSSCOPE Engine 3. - Supported new sensor offset of OS Boot Events for System Event Log(SEL) viewer on Web browser and Mail Alert. - Modified to close unused port(TCP/UDP port 427). - Took measures to GNU C library(glibc) vulnerable to buffer overflow (CVE-2015-7547). - Fixed the issue that it can not access to EXPRESSSCOPE Engine 3 from Web browser after changing BMC FW setting in rare case. - Update online help on Web browser of EXPRESSSCOPE Engine 3. --------------------------------------------------------------------------------------------------------- [ Legal notices (trademarks and copyrights) ] All contents on this software are the copyright of NEC Corporation or the third-party software developer. EXPRESSSCOPE is a registered trademark of NEC Corporation. Microsoft, Windows, Windows Vista and Windows Server are registered trademarks of Microsoft Corporation in the United States and other countries. Linux is a trademark or registered trademark of Linus Torvalds in the United States and other countries. This software uses the software under GNU General Public License or GNU Lesser General Public License. GRID is trademarks and/or registered trademarks of NVIDIA Corporation in the U.S. and/or other countries. All other product, brand, or trade names used in this publication are the trademarks or registered trademarks of their respective trademark owners. --------------------------------------------------------------------------------------------------------- Copyright NEC Corporation 2017 |