================================================================================
Express5800/T120h
System ROM U41 v1.32 (02/01/2018)
================================================================================
Software name : Express5800/T120h
System ROM (BIOS) update module
Models : Express5800/T120h
Operating System : This software supports offline update and the following OS.
- Windows Server(R) 2012 R2
- Windows Server(R) 2016
- Red Hat(R) Enterprise Linux(R) 7
Target Users : See [Target Users for Update] below
Type : System ROM
================================================================================
[About the software]
The Express5800/T120h System ROM (BIOS) update module supports the following
changes in the Express5800/T120h models:
Problems Fixed:
- Updated microcode for Intel(R) Xeon(R) Scalable Processors.
This version mitigates security vulnerability of INTEL-SA-00088 in Intel
Corporation.
- Addressed an issue where the system may experience an erroneous boot-time
message and Integrated Management Log (IML) entry stating that Core Boost
Technology is disabled due to a lack of an iLO Advanced License (531 -
Core Boost Technology missing required iLO License).
** Program and data included in this software **
Following program and data are included in this software.
Use one of them according to the way of installation.
a) Flash image for System Utilities/iLO Web User Interface
firmware\U41_1.32_02_01_2018.signed.flash
b) Executables for Windows(R)
winx64\cp034849.exe
c) RPM package for Linux(R)
Linux\firmware-system-oem-u41-1.32_2018_02_01-1.1.x86_64.rpm
-------------------------------------------------------------------------------
[ Target Users for Update ]
This software is available for the users who use the following models with the
following System ROM version.
- Models to be supported
1. Express5800/T120h
- System ROM Versions to be supported
1. U41 v1.20 (08/18/2017)
2. U41 v1.22 (09/29/2017)
3. U41 v1.26 (11/14/2017)
Note: In case of using newer System ROM from the above version, it has already
applied equivalent enhancements. Updating the System ROM isn't needed.
Be sure to check the System ROM version and date with the following procedures.
Select an arbitrary procedure and check the version before and after the update.
** System Utilities **
You can check the System ROM version and date by the following procedure.
1. Power on the system and the contents of process by POST (Power On Self-
Test) will be shown on the screen. After a short time, the following
message is shown. Press <F9> key, "System Utilities" is started.
[F9] System Utilities
2. After starting "System Utilities", select "System Information".
3. Select "Firmware Information".
4. Each firmware version is shown on the screen. The System ROM version and
date can be seen at "System ROM" option.
Note: After checking the System ROM version, press the <ESC> key or
select "Exit" to exit the System Utilities.
Note: About detail of "System Utilities" usage, refer to "1. System
Utilities" section in the chapter of "Useful Features" of the
maintenance guide.
** Windows(R) OS **
You can check the System ROM date by a following procedure.
1. Hold down <Windows> key and press <R> key.
2. In the "Run" dialog box, type "msinfo32" and then click "OK".
3. After "System Information" has started, select "System Summary".
4. Check the System ROM version by the profile of "BIOS Version/Date".
** Linux(R) OS **
You can check the System ROM date by a following procedure.
1. Launch the terminal such as xterm.
2. Execute the command as follows.
# /usr/sbin/dmidecode | less
Note: "#" means prompt. You do not need to input "#".
3. Check the System ROM date by "BIOS Information->Release Date".
Note: The dmidecode command has to be installed.
Be certain to read carefully the following NEC software license agreement
before applying this software update module. If you can not agree to the terms
of the agreement, do not download this software. By downloading the software
you will be bounded by the terms of the agreement.
<User License Agreement>
NEC Corporation ("NEC") grants you the right to use the software
program ("Software") under the terms and conditions of this Agreement
only in the country where you acquired the Software. You shall agree to all
provisions of this Agreement and assume responsibility for selection,
installation, use and effect of the Software purchased for your desired effect.
1. Period
1.1 This Agreement shall come into force on the day of the first download.
1.2 You may terminate the license granted hereunder by notifying us in writing
at least one month prior to the desired termination date.
1.3 NEC may terminate the license granted you hereunder at any time if you
fail to comply with any terms and conditions of this Agreement.
1.4 The license to the Software shall remain in force until the license is
terminated on the date set forth hereunder.
1.5 Upon termination of the license, other rights granted you hereunder shall
also be terminated. You must destroy, uninstall or dispose of the Software,
any copies of the Software and other materials provided with the Software.
2. Right of use
2.1 You may use the Software only on the purchased products, the products
which NEC defines as the supported models for the Software.
2.2 NEC grants you the right to use the Software only in the country in which
you acquired the Software in accordance with the conditions of the
preceding paragraph.
3. Intellectual Property Rights including patent and copyright
All of the intellectual property rights to the Software including patent
and copyright belong to NEC and/or the owners of the copyright or any
other intellectual property rights to the Software. No Intellectual
Property Rights including patent and copyright to the Software shall be
transferred to you. The Intellectual Property Rights can be protected as
a matter of Japan, U.S.A., and any other applicable laws and regulations.
4. Copying, altering, and combining of the Software
4.1 You may only make one copy of the Software solely for a backup purpose,
provided, however, that the copy of the Software is loaded into permanent
memory of the system (such as a hard disk drive). You may store the
Software solely to prevent damages or loss of the memory media.
4.2 You shall place the copyright notice and other legends on each copy of the
Software.
4.3 You may not use, copy, alter, combine, publish, reproduce the Software
over the Internet, or otherwise dispose of the Software except as provided
in this Agreement.
4.4 You may not copy, publish the manual and other related documentation
provided with the Software, or reproduce such manual and documentation
over the Internet.
4.5 No intangible property right to the Software shall be transferred to you.
5. Transfer
You may not sublicense, assign, transfer, or otherwise dispose of the Software
or the right of use to any third party except as provided herein.
6. Reverse compile
You may not reverse engineer, decompile, or otherwise disassemble the Software.
7. Limitation of warranties
7.1 THE SOFTWARE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. NEC
DISCLAIMS ALL WARRANTIES FOR THE SOFTWARE, EITHER EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. FURTHER, NEC MAKES NO REPRESENTATION OR WARRANTY THAT
THE USE OF ANY SOFTWARE WILL NOT INFRINGE ANY THIRD PARTY'S RIGHTS,
INCLUDING BUT NOT LIMITED TO, ANY INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT
SHALL NEC BE HELD LIABLE WITH RESPECT TO ANY CLAIM BY YOU OR ANY THIRD
PARTY ON ACCOUNT OF OR ARISING OUT OF THE USE OF THE SOFTWARE.
7.2 Notwithstanding the provisions of the preceding paragraph, in case NEC
makes any bug-fix version to the Software, NEC will, at its expense,
furnish you with such bug-fix version, update version, or information in
relation to such bug-fix or update version both in the source code form and
object code form, and such bug-fix version or update version shall be
considered as the licensed Software.
8. No liability
IN NO EVENT SHALL NEC BE LIABLE FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGES OR
LOSS OF PROFIT OR DAMAGES BASED ON ANY THIRD PARTY CLAIM, EVEN IF NEC HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
9. Miscellaneous
9.1 This Agreement shall be governed by the laws of the country in which you
acquired the Software.
9.2 You agree that NEC inspects the use of the Software and provides the
information of the inspection to the owner of the copyright to the
Software.
9.3 If the Software is licensed for use in the performance of a U.S. Government
prime contract or subcontract, You agree that, consistent with FAR 12.211
and 12.212, commercial computer Software, computer Software documentation
and technical data
for commercial items are licensed under this Agreement.
9.4 If the Software has a file written about software license (hereinafter
referred to as "License File"), the terms of License File are applied to
the files specified in License File, regardless of the above-mentioned
Agreement.
================================================================================
System ROM Installation Procedure
================================================================================
** System Utilities **
[ Preparation ]
- USB memory x1
1. Preparation of flash image (*.flash)
(1) Prepare the USB memory that is formatted with FAT or FAT32.
(2) Copy "a) Flash image for System Utilities/iLO Web User Interface file"
(approx. size 32MB) to a USB memory.
2. System ROM installation procedure
Install the System ROM by a following procedure.
(1) Attach the USB memory created in the procedure of "1" and power on the
system.
(2) In POST, press <F9> key to enter System Utilities.
(3) Select "Embedded Applications > Firmware Update > System ROM" menu.
(4) Choose "Select Firmware File", and then select the device in which flash
image was copied.
(5) Select flash image (i.e. *.flash).
(6) Select "Start Firmware Update".
(7) When the popup message of "Press ENTER to start firmware update.
This process might take a few minutes..." is shown, press <ENTER> key.
Update process is started.
(8) The progress of the update is shown. When it's completed, the popup
message of "Firmware update completed successfully." is shown. Press
<ENTER> key, the message is closed.
(9) Detach the Installation USB memory from the system.
(10) Reboot the system; Select the "Reboot the System" option at top
level menu of System Utilities.
(11) Wait reboot completion for update to take effect.
The installation is successfully finished.
** iLO Web User Interface **
1. Preparation of flash image (*.flash)
(1) Copy "a) Flash image for System Utilities/iLO Web User Interface file"
(i.e. *.flash) to any location which is accessible from the remote PC.
2. System ROM installation procedure
(1) Start the Web Browser on remote PC. And log-in to the iLO Web User
Interface by a "Configure to iLO Settings" privilege user.
(2) Select "Firmware & OS Software tab" from the right menu.
(3) Select "Update Firmware" from the left menu.
(4) Select the flash image, copied by a procedure of "1."
(5) Press "Flash" to begin update process.
(6) Wait for the "Firmware Update Completed." message to display.
(7) Reboot the system.
(8) Wait reboot completion for update to take effect.
The installation is successfully finished.
** Windows(R) OS **
1. Preparation of Installation
(1) Log on to the system as a user with administrator privilege.
(2) Terminate all running application.
(3) Copy "b) Executables for Windows(R) file" to a suitable
folder.
2. System ROM installation procedure
(1) Double-click "b) Executables for Windows(R) file" (i.e. *.exe).
The System ROM Update Program will start.
(2) Follow the messages will be shown and complete the operation.
(3) If the messages requesting reboot will be shown, select "yes" to reboot
of the system.
(4) Wait reboot completion for update to take effect.
The installation is successfully finished.
** Linux(R) OS **
1. Preparation of Installation
(1) Log-in as root. Or switch to root with "su" command.
(2) Terminate all running application.
(3) Copy "c) RPM package for Linux(R) file" to a suitable directory.
e.g. /root
2. System ROM installation procedure
(1) Install the RPM package of this System ROM update module by the command
below.
# rpm -Uvh <filename>.rpm
Note: The "<filename>.rpm" should replace to RPM package name which
is described at above "Binaries of this release" section.
Note: "#" means prompt. You do not need to input "#".
(2) See where the files land by the command below.
# rpm -qlp <filename>.rpm
(3) Change to the directory you see in the previous step.
(4) Run setup by the command below.
# ./setup
(5) Follow the messages will be shown and complete the operation.
(6) If a reboot inquiry is appear then press "y" to trigger reboot.
(7) Wait reboot completion for update to take effect.
The installation is successfully finished.
** Other OSes (e.g. VMware(R), etc.) **
Use the one of following procedures to update:
- Install the System ROM from System Utilities
- Install the System ROM from iLO Web User Interface
================================================================================
Notes
================================================================================
** Notes in general **
* Refer to "license_en.txt" about the user license agreement.
* When you install the system ROM, the flashing mechanism writes over the
backup ROM and saves current ROM as a backup, enabling you to switch easily
to the alternate ROM version if the new ROM becomes corrupted for any
reason. This feature protects the existing ROM version, even if you
experience a power failure while flashing the ROM.
* When Windows(R) BitLocker(TM) function is set to "Enabled", install the
System ROM after making the function "Disabled". Then make the function
"Enabled" after install and reboot of the system. If you install the system
ROM without making the function "Disabled", you may need the recovery
password when you boot the system.
* This software does not support a virtualized environment such as hyper
visor, guest OS, etc. Please install either on the OS which this software
supports or with the method of offline installation.
** Note for Windows(R) OS environment and Linux(R) OS environment **
* This software will access to iLO5 (Baseboard Management Controller). It is
required that the "iLO 5 Channel Interface Driver" (CHIF) must be installed.
The CHIF driver can be installed by using EXPRESSBUILDER or "Starter pack".
--------------------------------------------------------------------------------
[Revision history]
Version:1.32 (02/01/2018)
Problems Fixed:
- Updated microcode for Intel(R) Xeon(R) Scalable Processors.
This version mitigates security vulnerability of INTEL-SA-00088 in Intel
Corporation.
- Addressed an issue where the system may experience an erroneous boot-time
message and Integrated Management Log (IML) entry stating that Core Boost
Technology is disabled due to a lack of an iLO Advanced License (531 -
Core Boost Technology missing required iLO License).
Version:1.26 (11/14/2017)
Enhancements:
- Added support for update function of Innovation Engine (IE) Firmware.
Updating System ROM to v1.26 or later is needed to apply IE firmware and
SPS firmware.
Problems Fixed:
- Addressed an issue where the High Performance Event Timer (HPET) was
reported as "not functioning properly" under Device Manager on Windows(R).
Version:1.22 (09/29/2017)
Problems Fixed:
- Addressed an issue where the system would not achieve maximum performance
results when the BIOS/Platform Configuration (RBSU) Sub-NUMA Clustering
option is enabled. This option is not enabled by default.
- Addressed an issue where the system may have the system time incorrectly
"shifted" to the incorrect time after the operating system has been running
for an extended period of time. This issue was typically seen under
Microsoft Windows(R) when the Set Time Automatically option was enabled from
the Windows Date and Time Settings configuration page.
- Addressed an issue where the system may report an inaccurate error message
in the Integrated Management Log (IML) when a memory training failure
occurred. It is recommended that customers update to this version of the
system ROM before replacing any DIMMs due to a training issue.
- Addressed an issue where the system may experience an erroneous boot-time
message and Integrated Management Log (IML) entry stating that Core Boost
Technology is disabled due to a lack of an iLO Advanced License (531 - Core
Boost Technology missing required iLO License) when using the Version 1.20
System ROM.
--------------------------------------------------------------------------------
[Copyright and Trademark]
All contents on this software are the copyright of NEC Corporation or the
third-party software developer. All other contents mentioned herein are
copyright of their respective owners.
Microsoft, Windows, Windows Server are trademarks or registered trademarks of
Microsoft Corporation in the United States and other countries.
Linux(R) is a registered trademark of Linus Torvalds in the United States and
other countries.
Red Hat is a trademark or a registered trademark of Red Hat Inc. in the United
States and other countries.
All other company names and product names mentioned herein are registered
trademarks or trademarks of their respective owners.
--------------------------------------------------------------------------------
Copyright NEC Corporation 2018