================================================================================
Express5800/D120h
CMC firmware 01.30 (Offline Update)
================================================================================
Software name : Express5800/D120h
CMC firmware 01.30 (Offline Update)
Models : Express5800/D120h
Operating System : This software supports offline update
Target Users : See [Target Users for Update] below
Type : CMC firmware 01.30
================================================================================
[ About the software ]
This CMC firmware update module (hereinafter called "the software")
supports the following functional enhancement in the NEC Express5800/D120h
enclosure:
- Fixed possible intermittent fan full boost
- Fixed processor throlling issue of all server module when power supply unit
is degraded.
Note:
- To prevent a system failure, please read this document carefully and follow
the procedure for successful update. Should your system malfunctions or is
powered off due to an unplanned event during update (for example, power
blackout or cutoff, lightening, and noise), the system may be damaged and
fails to operate normally. In this case, any remedial measures shall be
taken at your expense.
-------------------------------------------------------------------------------
[ Target Users for Update ]
Users who use the following server models and CMC firmware need update:
- Target Server module:
NEC Express5800/D120h module enclosure
- CMC firmware
CMC firmware Revision: 01.24
NOTE:
If your CMC firmware revision are later than the above, you do not require the
update(the latest revisions already include the functions to be added by the
software).
How to confirm your CMC firmware revision:
* Confirmation from remote environment *
- By NEC ESMPRO Manager Ver.6:
(1) Run NEC ESMPRO Manager Ver.6 on remote PC.
(2) After selecting the server, select the [Remote Control] tab.
(3) Select the [IPMI Information] sub menu.
(4) Select the [MC(Management Controller) Information] sub menu.
(5) Select the [Basbrd Mgmt Ctlr] sub menu.
(6) The CMC firmware revision of your system will be displayed.
- By CMC Management Console function:
(1) Run CMC Management Console function.
(2) Select the [Properties] sub menu.
(3) The CMC firmware revision of your system will be displayed.
[User License Agreement]
NEC Corporation ("NEC") grants you the right to use the software program
("Software") under the terms and conditions of this Agreement only in the
country in which you acquired the Software. You shall agree to all provisions
of this Agreement and assume responsibility for selection, installation, use
and effect of the Software purchased for your desired effect.
1. Terms
1.1 This Agreement shall come into force on the date of your receipt of the
Software.
1.2 You may terminate the license granted hereunder by notifying us in writing
at least one month prior to the desired termination date.
1.3 NEC may terminate the license granted you hereunder at any time if you
fail to comply with any terms and conditions of this Agreement.
1.4 The license to the Software shall remain in force until the license is
terminated on the date set forth hereunder.
1.5 Upon termination of the license, other rights granted you hereunder shall
also be terminated. You must destroy or dispose of the Software, any copies
of the Software and manual and other materials provided with the Software.
2. Copyright
2.1 The Software shall solely be used in the NEC Express5800 servers.
2.2 NEC grants you the right to use the Software only in the country in which
you acquired the Software in accordance with the conditions of the
preceding paragraph.
3. Copying, altering, and combining of the Software
3.1 You may only make one copy of the Software solely for a backup purpose,
provided, however, that the copy of the Software is loaded into permanent
memory of the system. You may store the Software solely to prevent damages
or loss of the memory media.
3.2 You shall place the copyright notice and other legends on each copy of the
Software.
3.3 You may not use, copy, alter, combine, publish, reproduce the Software over
the Internet, or otherwise dispose of the Software except as provided in
this Agreement.
3.4 You may not copy, publish the manual or other related documentation
provided with the Software, or reproduce such manual and documentation over
the Internet.
3.5 No intangible property right to the Software shall be transferred to you.
4. Transfer
4.1 You may assign your rights granted hereunder to a third party only if all
conditions below are satisfied:
a. You shall assign and shall not retain this Agreement, the Software, all
copies of the Software, or the manual or other related documentation
provided with the Software.
b. The transferee agrees to this Agreement.
4.2 You shall not sublicense, assign, transfer, or otherwise dispose of the
Software or the right of use to any third party except as provided herein.
5. Reverse compile
You may not reverse engineer, decompile, or otherwise disassemble the
Software.
6. Limitation of warranties
6.1 The Software is provided "as is" without warranty of any kind. In no event
shall NEC be liable with respect to any claim by you on account of or
arising out of the use of the Software.
6.2 Notwithstanding the provisions of the preceding paragraph, in case NEC
makes any bug-fix version to the Software, NEC will, at its expense,
furnish you with such bug-fix version, update version, or information in
relation to such bug-fix or update version both in the source code form and
object code form, and such bug-fix version or update version shall be
considered as the licensed Software.
7. No liability
In no event shall NEC be liable for any indirect or consequential damages
or loss of profit or damages based on any third party claim, even if NEC
has been advised of the possibility of such damages.
================================================================================
CMC firmware Update Procedure
================================================================================
CMC update via CMC Management Console:
- How to get CMC web update image:
(1) Download the update module to a desired directory.
(2) Extract the downloaded module to a desired directory.
(3) The following files will be extracted to that specified folder.
- 130.img (web update image file)
- How to connect CMC Management Console:
Access the following URL from the web browser on the management
PC and please log in the CMC management console.
�@�@https://CMC IP address or https://CMC IP address
�@For details, Please refer to the BMC / CMC Management Console
User's Guide stored in EXPRESSBUILDER.
- How to update:
Notice:
While flashing, please be sure the system is power off.
(1) Select the [Update] item.
(2) Select [Firmware type] as [BMC].
(3) Click [Browse] to select the CMC web update image file.
(4) Click the [Upload] to upload the CMC firmware.
(5) After CMC firmware upload finished, click [Update] to update CMC
firmware.
(6) After [Status] is [100% Completed], the CMC firmware update is completed
and CMC is rebooting automatically.
(7) After around 90 seconds for CMC reboot.
(8) Plug out AC cable of enclosure.
(9) Wait 30 seconds and plug in AC cable of enclosure.
(10) Please confirm that the CMC firmware has been updated to the revision
listed below.
CMC Firmware Revision : 01.30
--------------------------------------------------------------------------------
Note
Note after the updated CMC firmware
(1) Logout all web browser on your system.
(2) Login the web browser on your system if necessary.
--------------------------------------------------------------------------------
[Revision history]
2018/7/3 CMCFW Revision 01.30
- Fixed possible intermittent fan full boost.
- Fixed processor throlling issue of all server module when power supply unit
is degraded.
--------------------------------------------------------------------------------
[Copyright and Trademark]
All contents on this software are the copyright of NEC Corporation or the third-
party software developer.
Microsoft, Windows, Windows Vista and Windows Server are registered trademarks
of Microsoft Corporation in the United States and other countries.
Linux is a trademark or registered trademark of Linus Torvalds in the United
States and other countries.
Red Hat and Red Hat Enterprise Linux are trademarks or registered trademarks
of Red Hat, Inc. in the United States and other countries.
This software uses the software under GNU General Public License or GNU Lesser
General Public License.
All other product, brand, or trade names used in this publication are the
trademarks or registered trademarks of their respective trademark owners.
--------------------------------------------------------------------------------
Copyright NEC Corporation 2018