======================================================================
Agentless Management Service for iLO Firmware 1.47 (for RHEL6.x)
======================================================================
[Software name ] Agentless Management Service (1.4.3)
[Registered name ] amsd-1.4.3-1193.10.rhel6.x86_64.zip
[Copyright (C) ] Hewlett Packard Enterprise
[Supported server models]
- Express5800/R120h-1M
- Express5800/R120h-2M
- Express5800/R120h-1E
- Express5800/R120h-2E
- Express5800/T120h
[Supported users ] All users who use the servers above with iLO
Firmware 1.47 with the Red Hat Enterprise Linux
Server versions below installed.
- Red Hat Enterprise Linux Server 6.9
- Red Hat Enterprise Linux Server 6.10
[Software type ] Utility
[Format ] zip file
======================================================================
[Software Introduction]
Agentless Management Service (hereinafter called "this software") is
a module required to get information of the host OS via the
Integrated Lights-Out Firmware (hereinafter called iLO).
Carefully read the following End User License Agreement before using
this software. If you do not agree to its terms, do not download this
software. By downloading this software, you agree to be bound by its
terms. Please store this document safely, as it will be needed when
uninstalling this software.
[End User License Agreement for NEC Software]
This End User License Agreement (hereinafter called "Agreement") is
an agreement between you and NEC Corporation (hereinafter called
"NEC"). Under the terms of this Agreement, NEC grants you the right
to use the software program (hereinafter called "Licensed Program"),
and you are to agree to the following terms. You are to take any
responsibility for the selection of, installation of, use of, or
results from the use of, the Licensed Program.
1. Terms and Termination
(1) This Agreement is effective from the date you receive the software
product.
(2) You may terminate the right to use the Licensed Program granted
under this Agreement at any time by giving NEC a written notice
no less than one month prior to the date you wish to do so.
(3) NEC may terminate your right to use the Licensed Program at any
time, if you fail to comply with the terms of this Agreement.
(4) Your right to use the Licensed Program continues to exist until
it is terminated in accordance with the provisions of this
Agreement.
(5) Immediately upon termination of your right to use the Licensed
Program, all of your other rights under this Agreement will be
terminated. You must destroy the Licensed Program, all copies
thereof, and any related documents (Eg. manuals) provided with
the Licensed Program.
2. Usage Right
(1) You may use the Licensed Program only on NEC Express5800 series
servers in which the following Red Hat Enterprise Linux Server
is installed.
- Red Hat Enterprise Linux Server 6.9
- Red Hat Enterprise Linux Server 6.10
3. Copying, Modifying, or Merging the Licensed Program
(1) You may make a single copy of the Licensed Program only for
backup purposes in case of data loss or corruption of the
Licensed Program. However, this does not apply where the
Licensed Program is installed in a fixed memory. In this case,
you may make a single copy of the Licensed Program only for
backup and storage purposes in case of loss or corruption of the
storage medium of the Licensed Program.
(2) You must display the Copyright and other proprietary rights
notices that appear on and in the Licensed Program on all copies
of the Licensed Program.
(3) Unless otherwise specified in this Agreement, you may not use,
copy, modify, or merge the Licensed Program, publish or
distribute any information or materials contained in the
Licensed Program through publications or through networks, or in
any manner other than as provided for in this Agreement.
(4) You may not copy the related documents (Eg. manuals) provided
with the Licensed Program, publish them in publications or
distribute them through networks under any circumstances.
(5) This Agreement does not transfer the intangible property rights
associated with the Licensed Program to you.
4. Transferring to a Third Party
(1) You may transfer all of your rights under this Agreement to a
third party, provided that all of the following conditions are
satisfied:
(a) You transfer this Agreement, the Licensed Program, all
copies of the Licensed Program, and all related documents
(Eg. manuals) provided with the Licensed Program to the
third party, and retain none of them.
(b) The transferee agrees to the terms of this Agreement.
(2) Unless otherwise specified in this Agreement, you may not rent or
lease the usage right of the Licensed Program, transfer the
Licensed Program to a third party, transport the Licensed
Program, or perform any other activity other than as granted in
this Agreement.
5. Decompilation
You may not carry out reverse engineering, decompililation, or
disassembly of the Licensed Program.
6. Warranty
(1) NEC does not provide any guarantee for the Licensed Program. You
are liable to pay for any costs arising from problems as a result
of the use of the Licensed Program.
(2) Irrespective of term (1), when NEC corrects Licensed Program
errors (bugs), NEC may, at its discretion, provide an
error-corrected program, a program for correction (hereinafter
called a "modification program"), or information for correction
by an NEC-decided method. The modification program provided to
you is regarded as the Licensed Program.
7. Limitation of liability
NEC assumes no liability for any lost profit, damages arising from
special circumstances (including damages which NEC can or could
foresee), or damages claimed to you by a third party.
8. Others
Disputes over this Agreement are to be settled at the Tokyo
District Court as the exclusively agreed competent court.
====================
Setup Procedure
====================
[Start Pack Installation]
(1) Before installing this software, please make sure to check
the current iLO5 Firmware version.
<Checking the iLO5 Firmware Version>
- By Looking at the Server Health Summary
Press the UID button on the server, and check the iLO5
Firmware version displayed on the monitor connected to the
server (See the iLO5 Users Guide for more information about
the Server Health Summary).
- Checking Remotely
Log in to the iLO Web Interface from a web browser on a
remote environment. Select "Firmware & OS Software", click
the "Firmware" tab, and check the iLO5 Firmware version.
(2) If the iLO5 Firmware version is older than 1.47, please
update the firmware by using the Starter Pack below before
installing this software.
For the installation procedure, access the link below, scroll
down to the "Using Offline Mode" section, and open the document
"Steps to update firmware by Starter Pack DVD". At Step(10) in
page 6, unselect all the firmware, then select only "Language
Pack" and "Online ROM Flash Component for Linux - iLO5", and
click "Deploy" (see page 7 for more information on how to
deselect and select components).
https://www.support.nec.co.jp/View.aspx?NoClear=on&id=
<ID *工事方法を確認>
[Updating from an Older Version]
(1) Using the command below, check whether this software is
already installed. If the command output includes a row starting
with "amsd" there is already a version of this software
installed, so please proceed to (2). If it returns no output,
please proceed to the [Installation Procedure] section below.
# rpm -q amsd
(2) Uninstall the installed software by following the steps in
the [Uninstallation Procedure] section below.
(3) Install this software by following the steps in the
[Installation Procedure] section below.
[Installation Procedure]
(1) Prepare the zip file (amsd-1.4.3-1193.10.rhel6.x86_64.zip).
(2) Relocate the zip file to a directory of choice on the OS,
and unzip it.
(3) Activate the terminal, move to the directory used in (2),
and install the software using the command below.
# rpm -ivh amsd-1.4.3-1193.10.rhel6.x86_64.rpm
(4) Check that the software installed correctly using the
command below.
# rpm -q amsd
amsd-1.4.3-1193.10.rhel6.x86_64
(5) Reboot the server using the command below.
# reboot
[Uninstallation Procedure]
(1) Uninstall the software using the command below.
Eg. For AMS1.4.3
# rpm -e amsd-1.4.3-1193.10.rhel6.x86_64
(2) Reboot the server using the command below.
# reboot
====================
Files List
====================
Length Date Time Name
--------- ---------- ----- ----
1493785 04-13-2020 10:30 amsd-1.4.3-1193.10.rhel6.x86_64.zip
You can check that the download package downloaded correctly by
comparing the MD5 checksum value below with the MD5 checksum value
of the file downloaded.
md5sum | Filename
---------------------------------+------------------------------------
003dcc1afdcfa53fc5576bfb132ffeb2 amsd-1.4.3-1193.10.rhel6.x86_64.zip
Length Date Time Name
--------- ---------- ----- ----
1503593 03-11-2020 09:27 amsd-1.4.3-1193.10.rhel6.x86_64.rpm
--------- -------
1503593 1 files
======================
Revisiion History
======================
2020/4/28 Agentless Management Service 1.4.3
- First Revision
----------------------------------------------------------------------
[Trademarks and Copyright]
The copyright for this software is held by Hewlett Packard
Enterprise.
NEC is permitted to distribute this software by Hewlett Packard
Enterprise.
* Red Hat is a registered trademark of Red Hat, Inc. in the United
States and/or other jurisdictions.
* All other company and product names in this document are the
registered trademarks or trademarks of their respective owners.
----------------------------------------------------------------------
Copyright NEC Corporation 2020