=========================================================================================================
Express5800/R120f-2E, Express5800/T120f
BMC firmware 02.16, SDR Rev 8
=========================================================================================================
Software name : Express5800/R120f-2E, Express5800/T120f
BMC firmware update module for Linux
Models : Express5800/R120f-2E, Express5800/T120f
Software revisions: See below
Type of software : BMC firmware
---------------------------------------------------------------------------------------------------------
[ About the software ]
BMC firmware and SDR update module("the software") supports the functional enhancement, which describe
Revision history, in Express5800/R120f-2E and Express5800/T120f models:
Note:
- To prevent a system failure, please read this document carefully and follow the procedure for
successful update. Should your system malfunctions or is powered off due to an unplanned event
during update (for example, power blackout or cutoff, lightening, and noise), the system may be
damaged and fails to operate normally. In this case, any remedial measures shall be taken at your
expense.
- This software does not support virtualization environment.
- If you use ESMPRO(R) ExpressUpdate function, [ 2. Models and software revisions for update ] and
[ 3. Installation procedures ] are processed automatically. Please refrer to [ 4. Notes ].
- Before BMC firmware update, please make sure that a drive letter has been assigned
to the virtual CD/DVD drive on Windows OS if the Remote Media function of the BMC firmware is enabled.
[ Models and software revisions to update ]
Users who use the following server models and BMC firmware versions need update:
- Models to update:
1. Express5800/R120f-2E
2. Express5800/T120f
- BMC firmware and SDR versions to update:
- BMC firmware
BMC Firmware Revision: 02.11
BMC Firmware Revision: 02.12
BMC Firmware Revision: 02.14
- SDR
SDR Revision: xx.x3
SDR Revision: xx.x5
NOTE:
If your BMC firmware version is later than the above, you do not require the update
(the latest versions already include the functions to be added by the software).
- How to confirm your BMC Firmware and SDR version:
Please make sure to confirm proper BMC Firmware and SDR version by any of the following means.(*1)
* How to confirm by the server which will be updated *
- By BIOS Setup, to confirm your BMC Firmware and SDR version:
(1) Power on the system.
(2) When the following message appears, press the F2 key to start the BIOS Setup Menu.
"Press <F2> to enter SETUP"
(3) Using the arrow keys, move the cursor to [Server].
(4) Select the [System Management] sub menu and press the Enter key.
(5) The software versions of your system will be displayed.
(6) After confirmation of the software versions, press the ESC key and exit the [System Management]
sub menu.
(7) Move the cursor to [Exit], using the arrow keys.
(8) Select [Exit Discarding Changes], and exit the BIOS Setup Menu.
* How to confirm by the remote access *
- By EXPRESSSCOPE Engine 3, to confirm your BMC Firmware and SDR version:
(1) Run EXPRESSSCOPE Engine 3.
(2) Select the [system] tab.
(3) Select the [IPMI information] sub menu.
Confirmation of BMC Firmware version
(4) Select the [MC] button and select [basbrd Mgmt Ctrl].
(5) Check [Firmware Revision].
Confirmation of SDR version
(6) Select the [SDR] button and select LAST Record ID / Record Type : OEMSDR
(7) Check [[OEM Dara] SDR Version].
- By ESMPRO Manager Ver.6, to confirm your BMC Firmware and SDR version:
(1) Run ESMPRO Manager Ver.6.
(2) After selecting the server, select the [Remote Control] tab.
(3) Select the [IPMI Information] sub menu.
Confirmation of BMC Firmware version
(4) Select the [MC(Management Controller) Information] sub menu.
(5) Select the [Basbrd Mgmt Ctlr] sub menu.
(6) The BMC firmware version of your system will be displayed.
Confirmation of SDR version
(7) Select the [SDR-Management Information] sub menu and press the Enter key.
(8) The SDR version of your system will be displayed.
Please read the following User License Agreement ("Agreement") carefully.
If you do not agree to the terms and conditions of this Agreement, you shall not download the Software.
Downloading the Software indicates your acceptance of the terms and conditions of the Agreement.
[User License Agreement]
NEC Corporation ("NEC") grants you the right to use the software program ("Software") under the terms
and conditions of this Agreement only in the country in which you acquired the Software. You shall
agree to all provisions of this Agreement and assume responsibility for selection, installation, use
and effect of the Software purchased for your desired effect.
<Agreement for the Software>
1. Terms
1.1 This Agreement shall come into force on the date of your receipt of the Software.
1.2 You may terminate the license granted hereunder by notifying us in writing at least one month
prior to the desired termination date.
1.3 NEC may terminate the license granted you hereunder at any time if you fail to comply with any
terms and conditions of this Agreement.
1.4 The license to the Software shall remain in force until the license is terminated on the date
set forth hereunder.
1.5 Upon termination of the license, other rights granted you hereunder shall also be terminated.
You must destroy or dispose of the Software, any copies of the Software and manual and other
materials provided with the Software.
2. Copyright
2.1 The Software shall solely be used in the NEC Express5800 servers.
2.2 NEC grants you the right to use the Software only in the country in which you acquired the
Software in accordance with the conditions of the preceding paragraph.
3. Copying, altering, and combining of the Software
3.1 You may only make one copy of the Software solely for a backup purpose,
provided, however, that the copy of the Software is loaded into permanent memory of the system.
You may store the Software solely to prevent damages or loss of the memory media.
3.2 You shall place the copyright notice and other legends on each copy of the Software.
3.3 You may not use, copy, alter, combine, publish, reproduce the Software over the Internet, or
otherwise dispose of the Software except as provided in this Agreement.
3.4 You may not copy, publish the manual or other related documentation provided with the Software,
or reproduce such manual and documentation over the Internet.
3.5 No intangible property right to the Software shall be transferred to you.
4. Transfer
4.1 You may assign your rights granted hereunder to a third party only if all conditions below are
satisfied:
a. You shall assign and shall not retain this Agreement, the Software, allcopies of the
Software, or the manual or other related documentationprovided with the Software.
b. The transferee agrees to this Agreement.
4.2 You shall not sublicense, assign, transfer, or otherwise dispose of the Software or the right of
use to any third party except as provided herein.
5. Reverse compile
You may not reverse engineer, decompile, or otherwise disassemble the Software.
6. Limitation of warranties
6.1 The Software is provided "as is" without warranty of any kind. In no event shall NEC be liable
with respect to any claim by you on account of or arising out of the use of the Software.
6.2 Notwithstanding the provisions of the preceding paragraph, in case NEC makes any bug-fix version
to the Software, NEC will, at its expense, furnish you with such bug-fix version, update version,
or information in relation to such bug-fix or update version both in the source code form and
object code form, and such bug-fix version or update version shall be considered as the licensed
Software.
7. No liability
In no event shall NEC be liable for any indirect or consequential damages or loss of profit or
damages based on any third party claim, even if NEC has been advised of the possibility of such
damages.
[ Installation procedures ]
- Procedure on Linux(R) Operating System
Perform the following steps to extract the Software and update your BMC firmware.
1.Switch to root user such as the "su" command.
2.Download the module into any directory of hard disk.
3.Extract the module into any directory.
4.The software and READE file will be extracted into the folder.
5.Execute the BMC firmware Update following the README file.
You can refer to the README file by Notepad of Windows(R) OS
---------------------------------------------------------------------------------------------------------
[ Revision history ]
2015/07/21 BMCFW Revision 02.16, SDR Revision xx.x8
BMC:
- Support N8118-303/N8118-304(2.5-inch PCIeSSD Installation Kit) in Express5800/R120f-2E
(N8100-2271F,N8100-2272F,N8100-2273F,N8100-2277F)
- Changed the encrypted communication not to use SSL v3.0.
- Improved the web server function of EXPRESSSCOPE Engine3 in order to show latest web contents
without browser cache clear after BMCFW update.
- Support for UEFI boot from Remote USB memory.
- Changed the sensor failure error detection method of the Power sensor.
- Changed to preserve accesslogs by EXPRESSSCOPE Profile Key when a motherboard is replaced.
- Improved to preserve contents of the web browser display for alert configurations
by EXPRESSSCOPE Profile Key when a motherboard is replaced.
- Fixed the issue that Server Configuration Utility can not apply configurations
when HTTP and HTTPS are disabled by Off-line TOOL Server Configuration Utility.
- Added the usable character "+" to the SMTP Server Setting in Mail Alert via a web browser.
SDR:
- Support N8118-303/N8118-304(2.5-inch PCIeSSD Installation Kit) in Express5800/R120f-2E
- Improved cooling condition when N8154-76(2.5-inch Hot Plug Drive Cage Kit) installed
in Express5800/R120f-2E(N8100-2277F).
2015/06/03 BMCFW Revision 02.14, SDR Revision xx.x5
BMC:
Support N8146-69(Dust Proof Bezel with Sensor) in Express5800/T120f
2015/04/20 BMCFW Revision 02.12, SDR Revision xx.x5
BMC/SDR:
Improved the issue that initial fan speed of some fans become to high after DC on.
2015/01/26 BMCFW Revision 02.11, SDR Revision 00.03
- Initial Release.
---------------------------------------------------------------------------------------------------------
[ Legal notices (trademarks and copyrights) ]
All contents on this software are the copyright of NEC Corporation or the third-party software
developer.
EXPRESSSCOPE is a registered trademark of NEC Corporation.
Microsoft, Windows, Windows Vista and Windows Server are registered trademarks of Microsoft
Corporation in the United States and other countries.
Linux is a trademark or registered trademark of Linus Torvalds in the United States and
other countries.
This software uses the software under GNU General Public License or GNU Lesser General Public License.
GRID is trademarks and/or registered trademarks of NVIDIA Corporation in the U.S. and/or other
countries.
All other product, brand, or trade names used in this publication are the trademarks or registered
trademarks of their respective trademark owners.
---------------------------------------------------------------------------------------------------------
Copyright NEC Corporation 2015