===============================================================================
N8103-149/150/151/160/N8403-059F/NE3703-001
RAID Controller Firmware Update Module
(Offline)
===============================================================================
Software name : N8103-149/150/151/160/N8403-059F/NE3703-001
RAID Controller Firmware Update Module
Models : Express5800/GT110f, GT110f-S, T110f-S, T110f-E, R110f-1E
GT110e, GT110e, GT110e-S, GT110e-S, GT110e-S
T110d, T120d, R110e-1E, R110e-1E, R110d-1M
R120d-1E, R120d-1M, R120d-2E, R120d-2M
E120d-1, E110d-M, E120d-M
B120e, B120d, B110d
Express5800/HR120a-1
Software version : 3.140.135-4041
Type of software : RAID Controller Firmware
===============================================================================
[ About the software ]
N8103-149/150/151/160/N8403-059F RAID controller firmware update module
(hereinafter referred to as "the software") is used for updating the firmware
of the following RAID controllers.
1) N8103-149/150/151/160
2) N8403-059F
[ Software versions that require the update ]
The following RAID Controller firmware versions need to be updated:
3.140.65-1587
3.140.75-1628
3.140.95-1967
3.140.115-2999
3.140.125-3364
NOTE:
If your RAID Controller firmware version is later than the above, the
update is not required (the latest revisions already include the functions
to be added by the software).
This update fixes the following phenomena.
<Modification made in 3.140.135-4041>
1) In some cases of using the HDD with more than 3TB, specific rare errors
may not be retried, and the HDD degeneration may be caused.
<Modification made in 3.140.125-3364>
1) There are cases when 6Gb SATA devices link up with 3G link speed.
<Modification made in 3.140.115-2999>
1) The trickle charge could not be performed in rare cases when you use
a Battery Backup Unit(BBU). If the BBU becomes not to perform the
trickle charge, capacitance becomes 0 mAh in about 10 months and then
BBU charging starts automatically after that. The charge would finish in 3
hours and recover. The cache policy would change to the write thru mode
for 2 hours during the process of the recovery.
2) The battery refresh may not be performed immediately when you operate to
execute the battery refresh. In this case the battery refresh will be
performed late.
<Modification made in 3.140.95-1967>
1) When booting the system, "BIOS Handshaking With The F/W,Wait..." is
sometimes displayed, and the operating system cannot be booted.
2) When using 4 RAID controllers, the following phenomena occur.
- Post stall occurs when console redirection is enabled.
- The RAID Controller status does not appear on EXPRESSSCOPE Engine 3.
<Modification made in 3.140.75-1628>
1) When booting the system, memory initialization of the RAID controller may
fail and the operating system cannot be booted.
[ How to confirm the RAID Controller firmware version ]
<Using WebBIOS>
1) Power on the system.
2) When the following message appears, press the <Ctrl> and <H> keys.
Press <Ctrl> <H> for WebBIOS
3) On the [Adapter Selection] screen, select the RAID Controller and click
the [Start] button.
4) Select [Controller Properties] of the left-side menu.
5) The RAID Controller firmware version of your system will be displayed.
<Using Universal RAID Utility (RAID Viewer)>
1) Start RAID Viewer.
2) Click the RAID Controller displayed on the Tree View.
3) Click [Properties] of the [File] menu.
4) In the [RAID Controller Properties] dialog box displayed, select the
[General] tab and check the value for "Firmware Version".
<Using Universal RAID Utility (raidcmd)>
1) Open a console window (Ex. command prompt).
2) Run the following command.
# raidcmd property -tg=rc -c=C <ENTER>
*note*
The "C" indicates the RAID Controller number.
3) The RAID Controller firmware version of your system will be displayed.
For more information on how to use WebBIOS and Universal RAID Utility, refer to
"N8103-149/150/151/160 RAID Controller User's Guide" and "Universal RAID
Utility User's Guide".
** NOTE **
* Incorrect update could result in the problems such as failure to boot the
system. Read through the instructions in this document carefully for
performing the update to prevent erroneous operation. When the system
malfunctions or the power is disconnected during the update due to unexpected
accidents such as power failure, lightning strike, power interruption and
noise, it may result in damage to the device and system malfunction in the
worst case. Please note that in such cases, repair may be required at your
cost.
Please read the following User License Agreement ("Agreement") carefully.
If you do not agree to the terms and conditions of this Agreement, you shall
not download the Software. Downloading the Software indicates your acceptance
of the terms and conditions of the Agreement.
-------------------------------------------------------------------------------
[User License Agreement]
NEC Corporation ("NEC") grants you the right to use the software program
("Software") under the terms and conditions of this Agreement only in the
country in which you acquired the Software. You shall agree to all provisions
of this Agreement and assume responsibility for selection, installation, use
and effect of the Software purchased for your desired effect.
The Software uses the software ("GPL Module") granted by GNU General Public
License("GPL) or GNU Lesser General Public License("LGPL"). This Agreement
does not cover GPL Module.
The Software includes the following GPL Module.
<GPL Module>
COMMAND.COM
KERNEL.SYS
FIND.COM
HIMEM.EXE
XCOPY.EXE
SRDISK.EXE
SRDXMS.SYS
syslinux
You can distribute or change the module based on the conditions of
GPL or any later Version, stipulated by Free Software Foundation. The module
is supposed to be useful, however, NEC does not guarantee it. In addition,
NEC does not release any copyright of GPL Module, designed by NEC.
== notice ==
The Free Software Foundation (FSF) is a non-profit corporation to support
the spread of the free software.
You need to refer to The Free Software Foundation ( https://www.fsf.org/ )for
details of GNU General Public License Version 2 and GNU Lesser General
Public License.
You shall agree that NEC does not answer to any questions regarding the GPL
Module.
By using the Software including GPL Module, you will be bounded by the terms
stipulated in GPL and LGPL.
This Agreement is applicable to the Software excluding GPL Module aforesaid.
1. Terms
1.1 This Agreement shall come into force on the date of your receipt of the
Software.
1.2 You may terminate the license granted hereunder by notifying us in
writing at least one month prior to the desired termination date.
1.3 NEC may terminate the license granted you hereunder at any time if you
fail to comply with any terms and conditions of this Agreement.
1.4 The license to the Software shall remain in force until the license is
terminated on the date set forth hereunder.
1.5 Upon termination of the license, other rights granted you hereunder shall
also be terminated. You must destroy or dispose of the Software, any
copies of the Software and manual and other materials provided with the
Software.
2. Copyright
2.1 The Software shall solely be used in the NEC Express5800 servers.
2.2 NEC grants you the right to use the Software only in the country in which
you acquired the Software in accordance with the conditions of the
preceding paragraph.
3. Copying, altering, and combining of the Software
3.1 You may only make one copy of the Software solely for a backup purpose,
provided, however, that the copy of the Software is loaded into permanent
memory of the system. You may store the Software solely to prevent
damages or loss of the memory media.
3.2 You shall place the copyright notice and other legends on each copy of
the Software.
3.3 You may not use, copy, alter, combine, publish, reproduce the Software
over the Internet, or otherwise dispose of the Software except as
provided in this Agreement.
3.4 You may not copy, publish the manual or other related documentation
provided with the Software, or reproduce such manual and documentation
over the Internet.
3.5 No intangible property right to the Software shall be transferred to you.
4. Transfer
4.1 You may assign your rights granted hereunder to a third party only if all
conditions below are satisfied:
a. You shall assign and shall not retain this Agreement, the Software,
all copies of the Software, or the manual or other related
documentation provided with the Software.
b. The transferee agrees to this Agreement.
4.2 You shall not sublicense, assign, transfer, or otherwise dispose of the
Software or the right of use to any third party except as provided
herein.
5. Reverse compile
You may not reverse engineer, decompile, or otherwise disassemble the
Software.
6. Limitation of warranties
6.1 The Software is provided "as is" without warranty of any kind. In no
event shall NEC be liable with respect to any claim by you on account of
or arising out of the use of the Software.
6.2 Notwithstanding the provisions of the preceding paragraph, in case NEC
makes any bug-fix version to the Software, NEC will, at its expense,
furnish you with such bug-fix version, update version, or information in
relation to such bug-fix or update version both in the source code form
and object code form, and such bug-fix version or update version shall be
considered as the licensed Software.
7. No liability
In no event shall NEC be liable for any indirect or consequential damages
or loss of profit or damages based on any third party claim, even if NEC
has been advised of the possibility of such damages.
8. Others
You must agree that any disputes concerning this Agreement will be settled
at the Tokyo district court as the exclusively appointed court.
===============================================================================
[ How to update the RAID Controller firmware ]
Perform the following steps to extract the Software and update your RAID
Controller firmware.
- How to extract:
1) Download the update module to a desired folder.
2) Extract the downloaded module to a desired folder.
3) The software (4041WEBC1.iso) and its installation procedures (readme_en.txt)
will be extracted to that specified folder.
- How to update:
1) Create the update CD using the ISO image.
2) Perform the steps of the readme file (readme_en.txt).
-------------------------------------------------------------------------------
[ Trademarks and Copyright ]
* c 2015 Avago Technologies
* EXPRESSSCOPE is a registered trademark of NEC Corporation.
* All other product, brand, or trade names used in this publication are the
trademarks or registered trademarks of their respective trademark owners.
-------------------------------------------------------------------------------
Copyright NEC Corporation 2015