================================================================================
NEC Express5800 Series
EXPRESSBUILDER Version E8.10-010.05
================================================================================
<Name> EXPRESSBUILDER Version E8.10-010.05
<Model(s)> Express5800/R120h-1M, R120h-2M, R120i-1M, R120i-2M, R120h-1E,
Express5800/R120h-2E, T120h, R110j-1
<Type> EXPRESSBUILDER
================================================================================
<Description>
EXPRESSBUILDER is installed into Express5800 series server and it can install
OS easily and maintain the server.
Version E8.10-010.05: Updated to FW version 3.81.2
Read carefully the following agreement before downloading.
If you do not agree to the terms of the agreement, do not download this software.
By downloading the software, you are bound by the terms of the agreement.
<User License Agreement>
NEC Corporation ("NEC") grants you the right to use the software
program ("Software") under the terms and conditions of this Agreement
only in the country where you acquired the Software. You shall agree to all
provisions of this Agreement and assume responsibility for selection,
installation, use and effect of the Software purchased for your desired effect.
1. Period
1.1 This Agreement shall come into force on the day of the first download.
1.2 You may terminate the license granted hereunder by notifying us in writing
at least one month prior to the desired termination date.
1.3 NEC may terminate the license granted you hereunder at any time if you
fail to comply with any terms and conditions of this Agreement.
1.4 The license to the Software shall remain in force until the license is
terminated on the date set forth hereunder.
1.5 Upon termination of the license, other rights granted you hereunder shall
also be terminated. You must destroy, uninstall or dispose of the Software,
any copies of the Software and other materials provided with the Software.
2. Right of use
2.1 You may use the Software only on the purchased products, the products
which NEC defines as the supported models for the Software.
2.2 NEC grants you the right to use the Software only in the country in which
you acquired the Software in accordance with the conditions of the
preceding paragraph.
3. Intellectual Property Rights including patent and copyright
All of the intellectual property rights to the Software including patent
and copyright belong to NEC and/or the owners of the copyright or any
other intellectual property rights to the Software. No Intellectual
Property Rights including patent and copyright to the Software shall be
transferred to you. The Intellectual Property Rights can be protected as
a matter of Japan, U.S.A., and any other applicable laws and regulations.
4. Copying, altering, and combining of the Software
4.1 You may only make one copy of the Software solely for a backup purpose,
provided, however, that the copy of the Software is loaded into permanent
memory of the system (such as a hard disk drive). You may store the Software
solely to prevent damages or loss of the memory media.
4.2 You shall place the copyright notice and other legends on each copy of the
Software.
4.3 You may not use, copy, alter, combine, publish, reproduce the Software
over the Internet, or otherwise dispose of the Software except as provided
in this Agreement.
4.4 You may not copy, publish the manual and other related documentation
provided with the Software, or reproduce such manual and documentation
over the Internet.
4.5 No intangible property right to the Software shall be transferred to you.
5. Transfer
You may not sublicense, assign, transfer, or otherwise dispose of the Software
or the right of use to any third party except as provided herein.
6. Reverse compile
You may not reverse engineer, decompile, or otherwise disassemble the Software.
7. Limitation of warranties
7.1 THE SOFTWARE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. NEC
DISCLAIMS ALL WARRANTIES FOR THE SOFTWARE, EITHER EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. FURTHER, NEC MAKES NO REPRESENTATION OR WARRANTY THAT THE USE OF ANY
SOFTWARE WILL NOT INFRINGE ANY THIRD PARTY'S RIGHTS, INCLUDING BUT NOT LIMITED
TO, ANY INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT SHALL NEC BE HELD LIABLE WITH
RESPECT TO ANY CLAIM BY YOU OR ANY THIRD PARTY ON ACCOUNT OF OR ARISING OUT OF
THE USE OF THE SOFTWARE.
7.2 Notwithstanding the provisions of the preceding paragraph, in case NEC
makes any bug-fix version to the Software, NEC will, at its expense,
furnish you with such bug-fix version, update version, or information in
relation to such bug-fix or update version both in the source code form and
object code form, and such bug-fix version or update version shall be
considered as the licensed Software.
8. No liability
IN NO EVENT SHALL NEC BE LIABLE FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGES OR
LOSS OF PROFIT OR DAMAGES BASED ON ANY THIRD PARTY CLAIM, EVEN IF NEC HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
9. Miscellaneous
9.1 This Agreement shall be governed by the laws of the country in which you
acquired the Software.
9.2 You agree that NEC inspects the use of the Software and provides the information
of the inspection to the owner of the copyright to the Software.
9.3 If the Software is licensed for use in the performance of a U.S. Government prime
contract or subcontract, You agree that, consistent with FAR 12.211 and 12.212,
commercial computer Software, computer Software documentation and technical data
for commercial items are licensed under this Agreement.
9.4 If the Software has a file written about software license (hereinafter referred
to as "License File"), the terms of License File are applied to the
files specified in License File, regardless of the above-mentioned Agreement.
================================================================================
Usage (Updating FW)
================================================================================
Please update the EXPRESSBUILDER according to the steps below.
Note: This update program does not work on iLO FW 1.xx. Run this program on iLO FW 2.xx.
- Checking version
[Using Local Console]
1. Run the System Utility from POST by pressing F9 key.
2. From [System Information] - [System Information] - [Firmware Information],
check EXPRESSBUILDER and BMC Firmware Version.
The BMC Firmware Version means iLO FW version.
[Using Remote Console]
1. Use the iLO web interface by referring to the iLO5 User's Guide.
2. From [Firmware & OS Software]-[Firmware], check the EXPRESSBUILDER and iLO5 Firmware.
If the EXPRESSBUILDER version is 3.81.2, the EXPRESSBUILDER is the latest version,
and you do not need to update the EXPRESSBUILDER.
If the iLO FW is 1.xx, you need to update to the iLO FW 2.xx in advance.
The iLO FW 2.xx is included in Starter Pack S8.10-010.05 or later.
- Preparing (creating update DVD):
1. Download files into any local folder on Windows environment.
2. Run e8.10-010.05.bat to create the ISO image file.
3. You can use the update DVD in one of following drives.
-- Virtual drive on remote console
-- Optical disk drive
See iLO5 User's Guide for details of Virtual drive and remote console.
Burn the ISO image file created at step 2 onto DVD-R as an ISO image when using an optical
disk drive.
- Updating:
1. Disable the secure booting.
Run System Utilities, and then proceed to Secure Boot Settings in System
Configuration > BIOS/Platform Configuration (RBSU) > Server Security.
2. If the iLO FW is 1.xx, update to the iLO FW 2.xx included in Starter Pack S8.10-010.xx by using offline mode.
3. Set the DVD created by "Preparing" into the server, or mount the ISO image file of
update DVD to a virtual drive when using remote console.
4. To run the "One-Time Boot", restart the server and press F11 key at POST.
5. From the menu, specify the drive that set the DVD at Step 3, and then the DVD will start automatically.
6. Wait until finishing updating without any operations (5~25 minutes).
Do not shut down or power off the server during updating.
7. The server will restart automatically after updating.
OS will start if an OS already has been installed.
8. Turn off the server, and then turn off AC power.
9. Wait for one minuite, and then turn on the server and run the EXPRESSBUILDER by pressing F10 key.
10. Click PERFORM MAINTENANCE, and then click System Erase and Reset.
11. Click EXPRESSBUILDER Preferences, and then click SUBMIT.
12. Click LAUNCH NOW.
13. After the erasing is finished, click REBOOT.
14. Press F10 key at POST to start EXPRESSBUILDER again.
15. The FIRST TIME SET UP WIZARD screen will appear.
Set your preference by referring the following supplement.
Supplement to Maintenance Guide
16. Install the latest Starter Pack according to the following website
after updating the EXPRESSBUILDER.
The version of Starter Pack that supported this firmware is S8.10-010.xx ('xx' is a two-digit number).
https://www.nec.com/express
- Related Links : Download
- Documents & Software
- (Select your server model)
17. Enable the secure booting if necessary.
--------------------------------------------------------------------------------
<Revision History>
2022/12/12 1st edition: Uploaded the E8.10-010.05
--------------------------------------------------------------------------------
<Copyright and Trademark>
All contents on this software are the copyright of NEC corporation or the third
party software developer.
* Microsoft, Windows, Windows Server, and BitLocker are trademarks or
registered trademarks of Microsoft Corporation in the United States
and other countries.
* All other product, brand, or trade names used in this document are
the trademarks or registered trademarks of their respective companies.
--------------------------------------------------------------------------------
Copyright NEC Corporation 2022